Lightsaver logo150 b2
tl_10
tr_10

bl_10

br_10

tl_10
tr_10
tl_10
tr_10

bl_10

br_10

MODEL LS – T166
5 WATT LED ALUMINIUM ALLOY FLASHLIGHT

TECHNICAL DATA SHEET
PHYSICAL AND MECHANICAL DATA

SIZE IN MILLIMETRES

WEIGHT

PACKAGING

LIGHT SOURCE

Head width        : 45 mm
Length               : 155 mm

  190 Gram

Box

5 Watt LED - 750 LUMEN



http://www.lightsaver.co.za Manufacturers of flashlights. Wholesales & distributor of flash lights and security equipmentPOWER SOURCE:  (Non rechargeable option - Primary batteries):  2 X CR123 Lithium- Ion batteries
    
                         (Rechargeable option) : 18650 Li-ion battery pack (3,7 V – 2,200 mAh )

OPTIONAL ACCESSORIES : (for rechargeable option)

  • Rechargeable battery pack (18650 Li-ion 3.7 V  2,200 mAh).
  • AC 220V Mains adaptor
  • DC 12V Cigarette plug Adaptor (car charger)
  • USB Smart charger / current control cable
  • Lithium Ion (18650) battery charger

BURN TIME:  (when battery is fully charged)

1. Constant burn time at 100%:    60 min

2. Constant burn time at 50%:     110 min

http://www.lightsaver.co.za Manufacturers of flashlights. Wholesales & distributor of flash lights and security equipment3. Constant burn time at 25%:     150 min

4. Constant burn time – Strobing : 60 min

5. Constant burn time S.O.S:      150 min

FEATURES:

  • 5 Mode settings: 100%, 50%, 25%, strobing , S.O.S
  • Super strong Aluminium alloy body
  • Military Spec Hard anodising (black)              
  • Cree LED – 100,000 hr lifetime
  • Lasts much longer than conventional incandescent globes
  • Highly improved reflector providing a concentrated focussed spot
  • Strike Bezel on head for close quarter defence
  • Impact resistant
  • Weather resistant

APPLICATION:

  • A law enforcement flashlight to use in all conditions and circumstances, robust enough to deal with rough handling and falling.
  • The disorientation effect allows the user to make arrests and deal with violent individuals in dangerous low light and dark conditions

OPERATING INSTRUCTIONS : (different modes follow sequentially – one after the other)

  • Press switch button once:-                        100%   Brightness
  • Press switch button again:-                        50%   Brightness           
  • Press switch button again:-                        25% Brightness
  • Press switch button again :-                       Flash
  • Press switch button again:-                        S.O.S
  • Press switch button again:-                        Flashlight switches off

CHARGING INSTRUCTIONS   - when rechargeable option is used:

  • Plug AC adapter into wall power outlet and insert USB connector (plug) of charger / current control cable into adapter.
  • Insert male socket of charger / current control cable into female socket of battery charger.
  • Insert rechargeable battery into battery charger
  • NB: Make sure battery / charger polarity is lined up correctly.
  • LED charger indicator in charger / current control cable ,will show ORANGE/ RED during charging and GREEN when battery is  fully charged
  • LED power indicator in battery charger will show RED continuously to indicate the power is ON. (will not change to     GREEN)
  • Charge time: approximately 4 hours.
  • Over time, unused batteries will discharge and must be recharged before use.
  • Use batteries only for intended purpose.
  • Disconnect chargers from power sources when not in use.
  • Do not leave flashlight unattended while ON.
  • CAUTION: Total discharge of battery (totally flat) is dangerous and will shorten battery life.

NOTE: This flashlight kit is equipped with an advanced charge controller, integrated into the charge cable and no damage will occur to the battery if charger is left on indefinitely.

charge profile

bl_10

br_10

Copyright © 2012 Lightsaver. All Rights Reserved Designed By: Coral Vine

POWERED BY 24WEB

Powered by 24web